Pond pumps, pool pumps, water feature pumps, marine aquarium pumps, solar pumps, and spa pumps operating costs are all being revolutionized with the new Energy Saving Pumps! The pump with a gas pedal! This adjustable horse power system has been proven by industry and power companies to save a lot of money. Order now and save 35%!

Our 2001 special we offer a 15% discount on all Sequence pump prices.

Click here to see an analysis of up front costs versus operating costs!

Sequence centrifugal pumps are designed and built to meet the special needs of ponds, waterscapes and aquaculture. Buying "quality" really pays. Not only do you get years of dependable service, but you enjoy tremendous savings on your utility bill, every month.

These are the work horses of the industry. They provide tremendous flow rates, with enough pressure (head) to handle the requirements of most systems with biological filters and moderate height waterfalls. They also are used extensively for the transfer and recirculation requirements of filtration systems, water features, streams, fountains and aquaculture. The flow rates range from about 2500 gph to 4800 gph and are customarily used on ponds from 2000 gallons on up.	For larger systems, plumb two or more units in parallel to economically multiply your flow. Units can be hard wired or if requested, can have cords with plug pre-installed. Housing is molded of glass filled Noryl®. Ports are 1-1/2" NPT on suction and discharge. Motors are enclosed for maximum protection.
		Click to enlarge then click your browsers back arrow to return

Click to Enlarge

Now you can get a smaller pump that has the same high quality as our larger units. The Sequence 750 provides its full rated flows, even with heads up to eight feet (unlike cheaper units which may lose over half their rated flow with this same head). Designed for flows from 500 to 2000gph, these units are perfect for ponds up to 2500 gallons.

Click to Enlarge

Model J8H3.11 J5H3.111 J2H3.111 Size 1/8 H.P. 1/8 H.P. 1/8 H.P. Head 12' Max. Head 12' Max. Head 11' Max. Head Flow 2000gph @ 8.5' 1600gph @ 8' 1200gph @ 8' Draw 138 Watts 117 Watts 107 Watts

Ports are 2" NPT suction and 1-1/2" NPT discharge. Units are pre-wired with an 8' cord and 115V plug. Housing is molded of glass filled polypropylene. The motors are enclosed, for excellent protection, at no extra charge.

 

Units have high quality, dual voltage motors. Suction and discharge ports are both 1-1/2" NPT. Seals for brackish or salt water are available. Motors are available single and three phase, ODP and TEFC. Model K661.111 K551.111 K441.111 K331.111 K221.111 K111.111 Size 2 H.P. 1.5 H.P. 1 H.P. 3/4 H.P. 1/2 H.P. 1/3 H.P. Head 87' Max. Head 84' Max. Head 82' Max. Head 79' Max. Head 72' Max. Head 66' Max. Head Flow 8160gph @ 43' 7440gph @ 36' 5880gph @ 24' 4980gph @ 14' 3300gph @ 7' 2200gph @ 1' Draw 25.0 Amps 19.4 Amps 16.5 Amps 12.3 Amps 8.8 Amps 8.7 Amps

When your application calls for higher flow rates and higher pressures, the Sequence 1000-3450 rpm units are your best buy! They are industrial grade units designed to produce good flow rates even when working against higher heads. The housings are injection molded of glass filled Noryl® for excellent strength and corrosion resistance.

 

The ports are 1" slip fit. Motors are 115V, single phase. Model F2SA1.111 Size 1/6 H.P. Head 43' Max. Head Flow up to 990gph Draw 2.8 max. Amp @ 115V

This pump is coupled to a 1/6 hp, 2 pole motor, and is designed for lower flow rates where a bit more pressure is needed. It is especially suited for fountains and aquarium systems.

Order now and save 35%! Flow rates up to 10,000 gpm at 100 feet of head!

         

  Sales: 303-883-8000

Energy Saving Pumps™

 Postal address: 5082 E. Hampden Ave, Suite #138  Denver, Colorado  80222     USA

Copyright © 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011  All Rights Reserved.